Abstract
A polystyrene (CH)/resorcinol formaldehyde (RF)/CH tri-layer perturbation target for hydrodynamic instability experiments in inertial confinement fusion (ICF) was designed and fabricated and its features were discussed. The target was composed of a perturbed CH layer, a RF aerogel sheet and an unperturbed CH layer. The detailed fabrication method consisted of four steps. An aluminum alloy template with sinusoidal perturbation patterns was prepared by the single-point diamond turning technology; the CH layer was prepared via a simple method which called dip-coating method; the RF aerogel sheet was prepared by sol–gel and supercritical drying process; finally, a CH layer, the RF aerogel sheet and another CH layer were put on the perturbed aluminum alloy template and hot-pressed at 150 °C for 2 h to make these three layers adhered together without the use of adhesive and to transfer the perturbation patterns from the template to the CH layer. A scanning electron microscope (SEM) was used to investigate the microstructure of the RF aerogel sheet. Parameters of the target, such as perturbation wavelength (T) and perturbation amplitude (A), were characterized by QC-5000 tool microscope and alpha-step 500 surface profiler. The results showed that T and A of the target were about 55 and 3.88 μm respectively, the perturbation patterns transferred from the alloy template to the CH layer precisely. Thickness of the perturbed CH layer (H1), RF aerogel sheet (H2) and unperturbed CH layer (H3) and cross-section of the tri-layer target were characterized by QC-5000 tool microscope and SEM. H1, H2 and H3 were about 50, 300 and 20 μm respectively, the cross-sectional photographs of the target showed that the CH layer and the RF aerogel sheet adhered perfectly with each other. As this CH/RF/CH tri-layer target use the RF aerogel to simulate the DT ice of the ignition target capsule, the whole target very close to the actual ignition target capsule.
Similar content being viewed by others
References
C. Cherfils, S.G. Glendinning, D. Galmiche et al., Convergent Rayleigh-Taylor experiments on the Nova laser. Phys. Rev. Lett. 83, 5507 (1999)
R.L. McCrory, R.E. Bahr, R. Betti et al., OMEGA ICF experiments and preparation for direct drive ignition on NIF. Nucl. Fusion 41, 1413 (2001)
C.C. Kuranz, R.P. Drake, M.J. Grosskopt et al., Three-dimensional blast-wave driven Rayleigh-Taylor instability and the effects of long-wavelength modes. Phys. Plasmas 16, 056310 (2009)
Y. Aglitskiy, A.L. Velikovich, M. Karasik et al., Direct observation of mass oscillations due to ablative Richtmyer-Meshkov instability in plastic targets. Phys. Rev. Lett. 87, 265001 (2001)
G. Huser, A. Casner, L. Masse et al., Reduced ablative Rayleigh-Taylor growth measurements in indirectly driven laminated foils. Phys. Plasmas 18, 012706 (2011)
J.D. Hager, V.A. Smalyuk, S.X. Hu et al., Study of Rayleigh-Taylor growth in directly driven cryogenic-deuterium targets. Phys. Plasmas 19, 072707 (2012)
M. Bono, D. Bennett, C. Castro et al., Fabrication of double shell targets with a glass inner capsule supported by SiO2 aerogel for shots on the omega laser in 2006. Fusion Sci. Technol. 51, 611 (2007)
A.K. Knight, F.Y. Tsai, M.J. Bonino et al., Suitability of different poly-imide capsule materials for use as ICF targets. Fusion Sci. Technol. 45, 187 (2004)
R.D. Richtmyer, Taylor instability in shock acceleration of compressible fluids. Commun. Pure Appl. Math. 13, 297 (1960)
M.D. Cable, S.P. Hatchett, J.A. Caird et al., Indirectly driven, high convergence inertial confinement fusion implosions. Phys. Rev. Lett. 73, 2316 (1994)
J. Kilkenny, K. Shillito, J. Kaae, et al., Inertial confinement fusion targets. General Atomics Report, 2005
K.O. Mikaelian, Design of a Rayleigh-Taylor experiment to measure strength at high pressures. Phys. Plasmas 17, 092701 (2010)
N. Metzler, A.L. Velikovich, A.J. Schmitt et al., Laser imprint reduction with a short shaping laser pulse incident upon a foam-plastic target. Phys. Plasmas 9, 5050 (2002)
X. Zhu, B. Zhou, A. Du et al., Potential SiO2/CRF bilayer perturbation aerogel target for ICF hydrodynamic instability experiment. Fusion Eng. Des. 87, 92 (2012)
Q. Yin, L. Zhang, S. Zhang et al., Fabrication of rippled plastic-foam targets used for hydrodynamic instability experiments. Fusion Sci. Technol. 61, 197 (2012)
X. Zhu, B. Zhou, Y. Zhong et al., Design and fabrication of CH/CRF dual-layer perturbation target for ICF hydrodynamic experiment. Nucl. Fusion 51, 083044 (2011)
J. Tang, Z. Xie, A. Du et al., Design and fabrication of a CH/Al dual-layer perturbation target for hydrodynamic instability experiments in ICF. Fusion Eng. Des. 89, 466 (2014)
Y. Zhong, B. Zhou, J. Gui et al., Fabrication of multilayer graded density peeled-carbon-aerogel target. Fusion Eng. Des. 86, 238 (2011)
M. Shukla, Y. Kashyap, P.S. Sarkar et al., Laser induced shock pressure multiplication in multi layer thin foil targets. Nucl. Fusion 46, 419 (2006)
H.C. Pant, M. Shukla, H.D. Pandey et al., Enhancement of laser induced shock pressure in multilayer solid targets. Laser Particle Beams 24, 169 (2006)
X. Zhu, B. Zhou, X. Xu et al., Fabrication of multi-layered shock wave tube for hydrodynamic instability experiment. J. Fusion Energ. 30, 509 (2011)
G.A. Kyrala, M.M. Balkey, C.W. Barnes et al., Target fabrication: a view from the users. Fusion Sci. Technol. 45, 286 (2004)
E.J. Hsieh, C.W. Hatcher, D.E. Miller, Fabrication of Rayleigh Taylor instability experiment targets. J. Vac. Sci. Technol., A 3, 1278 (1985)
C.-C. Yang, J.Y. Josefowicz, L. Alexandru, Deposition of ultrathin films by a withdrawal method. Thin Solid Films 74, 117 (1980)
Acknowledgments
This work was supported by National Natural Science Foundation of China (51102184, 51172163), Shanghai Committee of Science and Technology (12nm0503001), National Science and Technology Support Program (SQ2011BAJY3505) and National High Technology Research and Development Program of China (2013AA031801).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Tang, J., Xie, Z., Du, A. et al. Design and Fabrication of a CH/RF/CH Tri-Layer Perturbation Target for Hydrodynamic Instability Experiments in ICF. J Fusion Energ 35, 357–364 (2016). https://doi.org/10.1007/s10894-015-0037-y
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10894-015-0037-y