Abstract
A new test method was introduced to measure fiber distribution in steel fiber reinforced mortar by using image analysis technique. Through specimen preparation, image acquisition, fiber extraction, and measurement of related fiber parameters, quantitative analysis of fiber distribution could be obtained by two parameters, namely dispersion coefficient and orientation factor. Effect of boundaries, size and steel fiber content on fiber distribution was discussed. Results showed that, steel fiber distribution was affected by boundary effect, which would be weakened with the increase of specimen size. If the length and width remained constant, the specimen height had a significant effect on orientation factor of fiber, while its influence on dispersion coefficient was not so obvious. With the increase of steel fiber content, dispersion coefficient decreased slightly, and orientation factor deviated from 0.5.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Z A Lu, X C Fan, Y B Chen. Mechanical Properties of Layered Steel Fiber and Hybrid Fiber Reinforced Concrete[J]. J. Wuhan University of Technology-Mater. Sci. Ed., 2008, 23(5): 733–736
Y Akkaya, S P Shah, M Ghandehari. Influence of Fiber Dispersion on the Performance of Microfiber Reinforced Cement Composites[J]. ACI Special Publications 216: Innovations in Fiber-Reinforced Concrete for Value SP-216-1, 2003, 216: 1–18
J E Bolander, S Choi, S R Duddukuri. Fracture of Fiber-reinforced Cement Composites: Effects of Fiber Dispersion[J]. Int. J. Fract., 2008, 154: 73–86
N Ozyurt, T O Mason, S P Shah. Correlation of Fiber Dispersion, Rheology and Mechanical Performance of FRCs[J]. Cem. Concr. Compos., 2007, 29: 70–79
J L Chermant, L Chermant, M Coster, et al. Some Fields of Applications of Automatic Image Analysis in Civil Engineering[J]. Cem. Concr. Compos., 2001, 23: 157–169
C Redon, L Chermant, J L Chermant, et al. Assessment of Fibre Orientation in Reinforced Concrete using Fourier Image Transform[J]. J. Microsc., 1998, 191: 258–265
C Redon, L Chermant, J L Chermant, et al. Automatic Image Analysis and Morphology of Fibre Reinforced Concrete[J]. Cem. Concr. Compos., 1999, 21: 403–412
Y X Yang. Methods Study on Dispersion of Fibers in CFRC[J]. Cem. Concr. Res., 2002, 32: 747–750
J F Lataste, M Behloul, D Breysse. Characterisation of Fibres Distribution in a Steel Fibre Reinforced Concrete with Electrical Resistivity Measurements[J]. NDT and E Int., 2008, 41: 638–647
P Soroushian, C D Lee. Distribution and Orientation of Fibers in Steel Fiber Reinforced Concrete[J]. ACI Mater. J., 1990, 87(5): 433–439
Y H Lee, S W Lee, J R Youn, et al. Characterization of Fiber Orientation in Short Fiber Reinforced Composites with an Image Processing Technique[J]. Mater. Res. Innovations, 2002, 6:65–72
Y Akkaya, J Picka, and S P Shah. Spatial Distribution of Aligned Short Fibers in Cement Composites[J]. J. Mater. Civ. Eng., 2000, 12(3): 272–279
S I Torigoe, T Horikoshi, A Ogawa, et al. Study on Evaluation Method for PVA Fiber Distribution in Engineered Cementitious Composite[J]. J. Adv. Concr. Technol., 2003, 1(3): 265–268
J P Romualdi, J A Mandel. Tensile Strength of Concrete Affected by Uniformly Distributed and Closely Spaced Short Lengths of Wire Reinforcement[J]. ACI Mater. J., 1964, 61(6): 657–672
D Dupont, L Vandewalle. Distribution of Steel Fibres in Rectangular Sections[J]. Cem. Concr. Compos., 2005, 27: 391–398
G Zak, C B Park, B Benhabib. Estimation of Three-dimensional Fibreorientation Distribution in Short-fibre Composites by a Two-section Method[J]. J. Compos. Mater., 2001, 35(4): 316–339
Author information
Authors and Affiliations
Corresponding authors
Additional information
Funded by National Basic Research Program of China (973 Program) (No. 2009CB623200), National Natural Science Foundation of China (Nos. 50908104 and 50978126)
Rights and permissions
About this article
Cite this article
Liu, J., Sun, W., Miao, C. et al. Assessment of fiber distribution in steel fiber mortar using image analysis. J. Wuhan Univ. Technol.-Mat. Sci. Edit. 27, 166–171 (2012). https://doi.org/10.1007/s11595-012-0429-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11595-012-0429-z